dc-6.0 ghz ingap hbt mmic matched gain block amplifier page 1 of 7 mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2007 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. cgb7005-bd features chip layout low operating voltage: 5v 32.5 dbm output ip3 @ 850 mhz 3.2 db noise figure @ 850 mhz 21.0 db gain @ 850 mhz 17.6 dbm p1db @ 850 mhz low performance variation over temperature 100% dc on-wafer testing esd protection on all die: >1000v hbm low thermal resistance: <85oc/watt pa driver amp, if amp, lo buffer amp cellular, pcs, gsm, umts wireless data and satcom transmit and receive functions catv applications typical performance notes: 1. performance in mimix eval board, vs = 5 v, id = 63 ma typ., rbias = 15 , zs = zl = 50 , oip3 tone spacing = 1 mhz, pou t per tone = 3 dbm. 2. values reflect performance in recommended application circuit. 3. only on-wafer dc test is done. devices are not tested for rf performance. 850 mhz 1950 mhz 2400 mhz 3500 mhz units max. typ. min. max. typ. min. max. typ. min. max. typ. min. temperature (oc) parameter small signal gain output p1db output ip3 noise figure operating current input return loss output return loss pout @ -45 dbc, acp is-95, 9 forward channels +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 +25 -40 to +85 20.0 19.7 16.6 16.3 31.0 30.5 59 54 14 13 15 14 21.0 21.0 17.6 17.6 32.5 32.0 3.2 3.2 63 63 19 19 22 22 11 11 22.0 22.3 4.0 4.3 67 73 17.2 16.9 16.2 15.9 29.0 28.5 59 54 14 13 13.5 12.5 18.2 18.2 17.2 17.2 30.5 30.5 3.2 3.2 63 63 18 18 17.5 17.5 11 11 19.2 19.5 4.0 4.3 67 73 15.7 15.4 15.6 15.3 28.0 27.5 59 54 13 12 16 15 16.9 16.9 16.6 16.6 29.5 29.5 3.3 3.3 63 63 17.5 17.5 20 20 18.1 18.4 4.1 4.4 67 73 15.5 14.3 27.0 3.3 63 14.5 17 db db dbm dbm dbm dbm db db ma ma db db db db dbm dbm max device voltage max device current max device dissipated power rf input power storage temperature junction temperature operating temperature thermal resistance esd (hbm) +6.0 v 130 ma 0.65 w +17 dbm -55oc to 150oc 150oc -40oc to +85oc 85o c/w 1000 v absolute maximum ratings operation of this device above any of these parameters may cause permanent damage. april 2007 - rev 02-apr-07 description the cgb7005-bd is a darlington configured, high dynamic range, utility gain block amplifier. designed for applications operating within the dc to 6.0 ghz frequency range, mimix?s broadband, cascadable, gain block amplifiers are ideal solutions for transmit, receive and if applications. these mmic amplifiers are available in bare die form. mimix's ingap hbt technology and an industry low thermal resistance offers a thermally robust and reliable gain block solution. the ingap hbt die have extra pads to enable thorough dc testing. this unique test capability and the inclusion of esd protection on all die, significantly enhances the quality, reliability and ruggedness of these products. with a single bypass capacitor, optional rf choke and two dc blocking capacitors, this gain block amplifier offers significant ease of use in a broad range of applications.
page 2 of 7 typical s-parameter and noise performance dc-6.0 ghz ingap hbt mmic matched gain block amplifier mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2007 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. cgb7005-bd april 2007 - rev 02-apr-07
linearity performance - base station acp ? is-95 p1db vs frequency 8 10 12 14 16 18 012 3 456 frequency (ghz) p1db (dbm) 25 c -40 c 85 c oip3 vs frequency 26 28 3 0 3 2 3 4 0 0.5 1 1.5 2 2.5 33 .5 4 frequency (ghz) oip3 (dbm) 25 c -40 c 85 c 1 mhz separation, 3 dbm/tone page 3 of 7 typical power and linearity performance dc-6.0 ghz ingap hbt mmic matched gain block amplifier mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2007 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. cgb7005-bd april 2007 - rev 02-apr-07
page 4 of 7 typical scattering parameters ( v d = +4.15 v , icc = 61 ma, t = 2 3 c, device in a 50 ohm system) frequency s 11 s 21 s 12 s 22 (mhz) (mag) (ang) (mag) (ang) (mag) (ang) (mag) (ang) 100 0.052 -175.5 1 3 .02 17 3 .10 0.064 -0.61 0.02 3 -158. 3 200 0.05 3 -171.0 12.90 166. 3 0 0.064 -0.60 0.029 -14 3 .9 3 00 0.055 -166.7 12.78 159.70 0.064 -0.41 0.0 3 7-1 3 6.8 400 0.057 -16 3 .2 12.62 15 3 .20 0.065 -0.96 0.045 -1 3 4.6 500 0.059 -159.2 12.42 146.80 0.066 -1.24 0.05 3 -1 3 4.0 600 0.062 -156.1 12.22 140.40 0.066 -1.66 0.062 -1 3 5.2 700 0.065 -154.1 11.99 1 3 4.20 0.067 -2.21 0.069 -1 3 8.0 800 0.068 -152. 3 11.74 128.10 0.068 -2.57 0.076 -140.2 900 0.072 -150.2 11.49 122.10 0.069 - 3 .15 0.08 3 -14 3 .1 1000 0.076 -149. 3 11.2 3 116.20 0.070 - 3 .91 0.089 -146. 3 1100 0.080 -148.1 10.96 110.40 0.072 -4.69 0.095 -149.6 1200 0.084 -147.4 10.69 104.70 0.07 3 -5.51 0.098 -152.7 1 3 00 0.089 -146.8 10.42 99.16 0.075 -6.44 0.102 -155.7 1400 0.09 3 -146.5 10.15 9 3 .72 0.076 -7.4 3 0.105 -158.8 1500 0.098 -146.4 9.89 88.40 0.078 -8.49 0.108 -161.7 1600 0.10 3 -146.2 9.6 3 8 3 .15 0.080 -9.71 0.109 -164.6 1700 0.108 -146.5 9. 3 7 78.00 0.081 -10.91 0.111 -167. 3 1800 0.114 -146.9 9.12 72.94 0.08 3 -12.28 0.112 -170.0 1900 0.118 -147.6 8.88 68.02 0.085 -1 3 .6 3 0.11 3 -172.5 2000 0.12 3 -148.2 8.66 6 3 .14 0.087 -15.04 0.11 3 -175. 3 2100 0.129 -149.2 8.4 3 58. 3 0 0.089 -16.65 0.11 3 -177.7 2200 0.1 3 4 -150.1 8.21 5 3 .57 0.091 -18.25 0.112 179.9 2 3 00 0.140 -151.5 8.01 48.91 0.09 3 -19.90 0.112 177.5 2400 0.145 -15 3 .0 7.81 44. 3 0 0.095 -21.54 0.111 175.2 2500 0.150 -154.4 7.62 3 9.74 0.097 -2 3 . 3 1 0.110 172.7 2600 0.154 -156.2 7.44 3 5.26 0.099 -25.10 0.109 170.5 2700 0.159 -157.8 7.26 3 0.84 0.101 -26.97 0.108 168.1 2800 0.164 -159.9 7.10 26.47 0.104 -28.90 0.107 165.7 2900 0.168 -162.2 6.95 22.12 0.106 - 3 0.88 0.107 16 3 .2 3 000 0.17 3 -164.4 6.80 17.78 0.108 - 3 2.88 0.106 160.7 3 100 0.177 -166.8 6.66 1 3 .5 3 0.110 - 3 4.89 0.105 158.2 3 200 0.182 -169.2 6.5 3 9.26 0.11 3 - 3 7.02 0.105 155.4 33 00 0.186 -172.1 6.40 5.01 0.115 - 3 9.14 0.105 152.4 3 400 0.190 -175.1 6.28 0.76 0.118 -41.47 0.105 149.2 3 500 0.194 -178.1 6.16 - 3 .47 0.120 -4 3 .64 0.105 146.0 3 600 0.198 178.8 6.04 -7.68 0.12 3 -45.97 0.104 142.8 3 700 0.201 175.4 5.94 -11.84 0.125 -48. 3 2 0.104 1 3 8.8 3 800 0.204 171.9 5.8 3 -16.02 0.128 -50.68 0.105 1 3 4.5 3 900 0.207 167.8 5.74 -20.19 0.1 3 0-5 3 .1 3 0.105 1 3 0.0 4000 0.209 16 3 .9 5.64 -24. 33 0.1 33 -55.5 3 0.106 125. 3 4100 0.210 159.7 5.55 -28.49 0.1 3 6 -58.04 0.107 120.0 4200 0.211 155.5 5.47 - 3 2.64 0.1 3 8 -60.60 0.109 114. 3 4 3 00 0.211 150.6 5. 3 8- 3 6.80 0.141 -6 3 .20 0.111 108.4 4400 0.212 145.6 5. 3 1 -40.98 0.14 3 -65.80 0.114 101.7 4500 0.212 140. 3 5.2 3 -45.18 0.146 -68.52 0.118 95.0 4600 0.212 1 3 5.1 5.15 -49. 3 5 0.149 -71.22 0.12 3 88.66 4700 0.211 129.6 5.08 -5 3 .55 0.151 -7 3 .90 0.128 82. 3 2 4800 0.211 12 3 .6 5.01 -57.75 0.154 -76.77 0.1 3 5 75.66 4900 0.212 116.9 4.95 -62.01 0.157 -79.70 0.144 68.9 3 5000 0.21 3 110.0 4.88 -66. 3 1 0.159 -82.64 0.154 62.1 3 continues n ext page. s-parameter data files are available online at: www.mimixbroadband.com dc-6.0 ghz ingap hbt mmic matched gain block amplifier mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2007 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. cgb7005-bd april 2007 - rev 02-apr-07
page 5 of 7 typical scattering parameters ( v d = +4.15 v , icc = 61 ma, t = 2 3 c, device in a 50 ohm system) frequency s 11 s 21 s 12 s 22 (mhz) (mag) (ang) (mag) (ang) (mag) (ang) (mag) (ang) 5100 0.214 10 3 . 3 0 4.81 -70.61 0.162 -85.61 0.16 3 55.60 5200 0.215 96.45 4.75 -74.87 0.164 -88.60 0.172 49.58 5 3 00 0.217 89.12 4.69 -79.25 0.167 -91.68 0.186 4 3 .71 5400 0.221 81.08 4.6 3 -8 3 .69 0.169 -94.88 0.200 3 7. 3 4 5500 0.226 7 3 .02 4.56 -88.08 0.172 -98.04 0.215 3 1.12 5600 0.2 3 2 65.24 4.50 -92.47 0.174 -101.20 0.229 25.49 5700 0.240 57.44 4.44 -96.98 0.176 -104.60 0.246 20.26 5800 0.249 49.5 3 4. 3 8 -101.60 0.178 -108.00 0.264 14.56 5900 0.259 41.22 4. 3 0 -106.10 0.179 -111.40 0.284 8.86 6000 0.271 33 .24 4.2 3 -110.70 0.181 -114.80 0. 3 04 3 .61 6100 0.286 25.66 4.16 -115. 3 0 0.182 -118. 3 00. 3 25 -1.54 6200 0. 3 00 18.46 4.08 -119.90 0.18 3 -121.80 0. 3 46 -6.54 6 3 00 0. 3 15 11.28 4.01 -124.50 0.184 -125. 3 00. 3 67 -11.4 3 6400 0. 33 1 4.04 3 .9 3 -129.20 0.184 -128.90 0. 3 89 -16.17 6500 0. 3 49 -2.90 3 .84 -1 33 .90 0.185 -1 3 2.50 0.412 -20.99 6600 0. 3 68 -9. 33 3 .75 -1 3 8.50 0.185 -1 3 6.10 0.4 3 4 -25.65 6700 0. 3 86 -15.29 3 .67 -14 3 .10 0.185 -1 3 9.60 0.455 - 3 0.14 6800 0.404 -21.22 3 .58 -147.70 0.184 -14 3 .20 0.476 - 3 4.47 6900 0.421 -27.17 3 .49 -152. 3 0 0.18 3 -146.80 0.496 - 3 8.81 7000 0.440 - 33 .06 3 . 3 9 -156.90 0.182 -150.40 0.518 -4 3 .21 7100 0.459 - 3 8.62 3 .29 -161.40 0.180 -15 3 .90 0.5 3 8 -47.40 7200 0.477 -4 3 .70 3 .20 -165.80 0.179 -157.40 0.557 -51.69 7 3 00 0.49 3 -48.72 3 .11 -170. 3 0 0.177 -160.80 0.574 -55.75 7400 0.508 -5 3 .8 33 .01 -174.70 0.175 -164.20 0.591 -59.68 7500 0.524 -58.82 2.91 -179.00 0.17 3 -167.70 0.608 -6 3 .66 7600 0.540 -6 3 .55 2.82 176.70 0.170 -170.90 0.624 -67.57 7700 0.555 -68.01 2.72 172.50 0.168 -174.10 0.6 3 9 -71.29 7800 0.567 -72.18 2.6 3 168.50 0.165 -177. 3 0 0.652 -74.92 7900 0.579 -76. 3 5 2.54 164.40 0.16 3 179.60 0.664 -78.40 8000 0.589 -80.64 2.46 160. 3 0 0.160 176.60 0.676 -81.79 8100 0.601 -84.7 3 2. 3 7 156.40 0.157 17 3 .50 0.688 -85.25 8200 0.612 -88.46 2.28 152.60 0.154 170.60 0.699 -88.48 8 3 00 0.621 -91.94 2.20 148.90 0.152 167.80 0.709 -91.59 8400 0.628 -95. 33 2.1 3 145. 3 0 0.149 165.00 0.717 -94.6 3 8500 0.6 3 4 -98.91 2.06 141.60 0.147 162.20 0.724 -97.60 8600 0.640 -102.50 1.98 1 3 7.90 0.144 159. 3 0 0.7 3 1 -100.50 8700 0.647 -105.90 1.92 1 3 4.40 0.141 156.70 0.7 3 8 -10 3 .40 8800 0.654 -108.90 1.85 1 3 1.00 0.1 3 8 154. 3 0 0.744 -106.20 8900 0.656 -111.80 1.79 127.60 0.1 3 6 151.90 0.748 -108.70 9000 0.658 -114.90 1.7 3 124. 3 0 0.1 3 4 149.40 0.75 3 -111.40 9100 0.660 -118.10 1.68 120.90 0.1 3 2 146.80 0.757 -114.00 9200 0.66 3 -121. 3 0 1.62 117.50 0.129 144.40 0.761 -116.40 9 3 00 0.666 -124.10 1.57 114. 3 0 0.127 142.10 0.765 -118.90 9400 0.668 -126.70 1.52 111.10 0.125 1 3 9.80 0.769 -121.40 9500 0.667 -129.40 1.47 107.90 0.12 3 1 3 7.40 0.770 -12 3 .60 9600 0.666 -1 3 2. 3 0 1.4 3 104.80 0.121 1 3 5.10 0.77 3 -126.00 9700 0.666 -1 3 5.20 1. 3 8 101.60 0.119 1 3 2.70 0.776 -128. 3 0 9800 0.668 -1 3 7.90 1. 3 4 98.51 0.117 1 3 0.50 0.778 -1 3 0.50 9900 0.668 -140.20 1.29 95.57 0.115 128.40 0.780 -1 3 2.70 10000 0.665 -142.40 1.26 92.60 0.11 3 126.40 0.782 -1 3 4.80 s-parameter data files are available online at: www.mimixbroadband.com dc-6.0 ghz ingap hbt mmic matched gain block amplifier mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2007 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. cgb7005-bd april 2007 - rev 02-apr-07
page 6 of 7 application circuit recommended bias resistor values for id = 63 ma supply voltage (vs) 5v 7v 8v 10v rbias (1/4w) 15 47 63 ?? rbias (1/2w) ?? note: rbias provides dc bias stability over temperature. 2 rf in vs rf out c1 c2 note: this schematic represents the topology of the application circuit recommended by mimix. uuuu l1 r bias = (vs - vd) / id 4 3 1 vd r1 c3 94 dc-6.0 ghz ingap hbt mmic matched gain block amplifier mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2007 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. cgb7005-bd april 2007 - rev 02-apr-07 ref designator value c1, c2 1000 pf c3 1.0 f l1 56 nh d i / ) d v - s v ( = s a i b r 1 r physical dimensions bonding configuration
page 7 of 7 dc-6.0 ghz ingap hbt mmic matched gain block amplifier mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2007 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. cgb7005-bd april 2007 - rev 02-apr-07 handling and assembly information caution! - mimix broadband mmic products contain gallium arsenide (gaas) which can be hazardous to the human body and the environment. for safety, observe the following procedures: do not ingest. do not alter the form of this product into a gas , powder, or liquid through burning, crushing, or chemical processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed. observe government laws and company regulations when discarding this product. this product must be discarded in accordance with methods specified by applicable hazardous waste procedures. life support policy - mimix broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the president and general counsel of mimix broadband. as used herein: (1) life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) a critical component is any compone nt of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. esd - gallium arsenide (gaas) devices are susceptible to electrostatic and mechanical damage. die are supplied in antistatic containers, which should be opened in cleanroom conditions at an appropriately grounded anti-static workstation. devices need careful handling using correctly designed collets, vacuum pickups or, with care, sharp tweezers. die attachment - gaas products from mimix broadband are 0.100 mm (0.004") thick. microstrip substrates should be brought as close to the die as possible. the mounting surface should be clean and flat. if using conductive epoxy, recommended epoxies are tanaka ts3332ld, die mat dm6030hk or dm6030hk-pt cured in a nitrogen atmosphere per manufacturer's cure schedule. apply epoxy sparingly to avoid getting any on to the top surface of the die. an epoxy fillet should be visible around the total die periphery. for additional information please see the mimix "epoxy specifications for bare die" application note. wire bonding - windows in the surface passivation above the bond pads are provided to allow wire bonding to the die's gold bond pads. the recommended wire bonding procedure uses gold 0.025 mm (0.001") diameter ball bonds. aluminum wire should be avoided. thermo-compression bonding is recommended though thermosonic bonding may be used providing the ultrasonic content of the bond is minimized. bond force, time and ultrasonics are all critical parameters. bonds should be made from the bond pads on the die to the package or substrate. all bonds should be as short as possible. part number for ordering description CGB7005-BD-000V rohs compliant die packed in vacuum release gel paks
|
